Get an instant quote

Resources / How freight class is derived, and how to document it

Resource

How freight class is derived, and how to document it

Freight class is not a carrier opinion formed on the day of pickup. It is derived from what the shipment is, how dense it is, how it must be handled and what it is worth if lost — and it is fixed by the documentation provided at booking. This guide shows the inputs, the worksheet and the reason reclass happens.

Last reviewed . The date moves only when the claims on this page are re-checked against the published rate and policy pages.

Get an instant quote See the rate basis

Class is a rate basis, not a label

Freight class is the NMFC category that tells a carrier what the shipment is and what it takes to move it. In the estimate model it is a multiplier: the LTL arithmetic is computed, then adjusted by the class factor published on the rate basis page.

That makes class a claim about the freight, not a formality. If the class on the BOL describes a denser, easier or less valuable shipment than the one on the dock, the carrier can reclass it — and the rate changes after delivery, when the argument is expensive. The published basis, including the class multiplier, is on the rate basis page.

The estimate model prices these classes: 50, 55, 60, 65, 70, 77.5, 85, 92.5, 100, 110, 125, 150, 175, 200, 250, 300, 400, 500. Classes outside that list are quoted by dispatch rather than guessed by the form.

The commodity description belongs to the shipper or consignee. Dispatch re-checks the class against the measurements you send; it does not invent a class to make a number work.

Density: weight over cubic feet

Density is the first input and the one most often estimated rather than measured. Measure every handling unit — pallet and overhang included — in inches, convert to cubic feet, add the units together, then divide total weight by total cubic feet.

Cubic feet per unit = (length x width x height in inches) / 1,728. Density = total weight in lb / total cubic feet.

A shipment whose cartons sit on a pallet has to be measured as it will be handled, not as the carton manufacturer lists it. The same units on a tight, square pallet and on an overhanging, irregular pallet are different shipments for a trailer.

If you cannot measure before booking, say so. Dispatch can quote from a documented assumption, but the assumption is written on the quote rather than discovered at the terminal.

Handling and liability: the other two inputs

Density alone does not set the class. Two shipments of the same density can land in different classes because of how they must be handled and what they are worth per pound.

  • Handling: fragile or crushable freight, freight that cannot be stacked, freight that needs two people or a liftgate, hazardous material and anything with a loading constraint.
  • Liability: value per pound, susceptibility to theft or damage, and whether a loss would be a repair, a replacement or a business interruption.
  • Packaging: whether the packaging protects the freight through shared-trailer handling and whether it is itself the shipping unit.

These inputs are why a class cannot be computed from density alone even though density is the largest single contributor. The classification is a judgement recorded in the NMFC, and the carrier applies it against the shipment as described.

Document it before you book, and why reclass happens

Reclass is usually a documentation failure, not a carrier decision made in bad faith. The file that prevents it is small:

  • Dimensions per handling unit: length, width and height in inches, with the pallet and any overhang included.
  • Actual weight: weighed, not estimated from an invoice or a packing slip.
  • Piece and pallet count: how the shipment will actually be handled, not how it was ordered.
  • Commodity description: what it is, what it is made of, and whether it is hazardous, fragile or temperature-sensitive.
  • Packaging and stackability: whether it can be stacked, and what happens to it if it is.

Send those with the quote request and keep them with the BOL. If the terminal measures something different, the file shows what was documented at booking — which turns the conversation into a comparison of two measurements instead of an argument about a charge.

Book the lane on the quote form, and read the LTL vs FTL guide if the class result changes which mode makes sense: when less-than-truckload beats a full trailer.

This guide describes the inputs and the paperwork. The class itself comes from the NMFC and the commodity; it is not a number this site can assign without the shipment description.

Questions

Is freight class the same as density?

No. Density is one of the inputs. Class also reflects handling and liability, and the classification comes from the NMFC commodity description rather than from a density calculation alone.

What measurements should I send at booking?

Length, width and height per handling unit in inches, including the pallet and any overhang; the actual weight; the piece and pallet count; and whether the freight can be stacked.

Why did the carrier reclass my shipment?

Usually because the dimensions or weight on the BOL differ from what the terminal measured, or because the commodity description implies more handling or liability than the class assumed. Measure and document at booking rather than argue after delivery.

Can Portlandia tell me which class to use?

Dispatch re-checks the class against the measurements and weight you provide, but the commodity description belongs to the shipper. We flag a mismatch before the rate is confirmed; we do not invent a class to make a number work.

Ask the desk

Mon–Fri 8:00am–6:00pm ET. Questions about a lane or a document are answered in writing.

(502) 385-3399 Get an instant quote

Arranging entity

Freight arrangements are made through Dynamic Distribution Solutions LLC dba Portlandia Logistics. Authority status →

Send the dimensions with the quote

Measured dimensions, actual weight and a commodity description cost a few minutes at booking and remove the most common line item that shippers dispute after delivery.

Quote with the class detail